How To Set Time Zone On Atomic Clock

Download Article

Download Article

SkyScan makes over 40 models of atomic clocks, and they all transmit the time from the National Institute of Standards and Technology. It is estimated that they deviate by less than one second inside 3,000 years. Choose the correct setting process co-ordinate to whether your clock is a digital clock, weather station, or standard clock face.

1. ane

   Insert two AA, LR6 i.v volt alkaline batteries in the battery compartment of the clock. Align them in the compartments based on the polarity marked on the clock's compartment case. The clock will search for a bespeak once the batteries are installed. Wait at least 15 minutes for the temperature to display on the clock before setting it.^[1]

2. 2

   Slide the fourth dimension zone switch on the back of the clock or press the fourth dimension zone button. ^[2] The time zone will flash and at that point, you tin can input the desired fourth dimension zone past pressing and releasing the "+" key. PST is Pacific Standard Time, MST is Mount Standard Time, CST is Cardinal Standard Time, and EST is Eastern Standard Time.

   Advertisement

3. three

   Begin to manually set the fourth dimension on your clock. Slide the Daylight Saving Time switch to "On" if yous are in Daylight Savings Time. Switch it to "Off" if it is not Daylight Savings Time.^[3] This selection may not be bachelor on all clocks.

4. 4

   Set the time on your clock with your desired hours. Afterward adjusting the time zone and daylight savings (equally described in the previous step), the hr digit on the clock will start to flash automatically. Printing and release the "+" key until it'southward the at the desired 60 minutes. Printing "SET" to secure the fourth dimension.^[four]

   • The minute digits will brainstorm to flash once the hour digit has been set in identify. Printing and release the "+" central until it's at the right infinitesimal.
   • Press and release the "SET" key to move to setting the "year". Repeat this activeness to set the month, date, weekday, 12/24H time format, and temperature setting.
   • Recollect that if fix properly, SkyScan clocks are able to set themselves. So although you tin can manually ready the time, understand that the time may modify accurately on its ain and void your manual efforts.

5. 5

   Place your atomic clock near a window, away from metal and concrete structures. Exit it for at least 4 minutes then that it can find the signal. Information technology will automatically search for a bespeak at two AM for eight minutes each night.^[5]

Advertisement

1. 1

   Fix one to three of the transmitters on the clock/weather station. Transmitters display the current humidity and temperature indoors and outside that the remote unit monitors. Remove the transmitter from the stand and unscrew the battery door of the transmitter. Place two AAA batteries in each battery compartment.^[6]

2. 2

   Assign a channel to each transmitter yous plan to employ. Receivers can receive temperature and humidity information from upward to three transmitters at a time, as reflected by assigned channels. In one case channels have been assigned to a transmitter, they can but exist changed by removing the batteries and resetting the transmitter over once more.^[7]

   • Slide the switch inside of the battery compartment for each transmitter you're using. There will be a switch for Channel 1, 2, and Channel 3 respectively.

3. three

   Confirm the channel setting by pressing the "Reset" push. The "Reset" button is inside the battery compartment using a small pin. Slide the C/F switch inside of the compartment for centigrade or Fahrenheit. Replace and screw in the bombardment cover.

4. iv

   Avoid placing the transmitter in pelting, snow or direct sunlight. The clock on the transmitters and weather station will be controlled via radio signal. You lot tin too press "Reset" to recalibrate the unit.

5. v

   Remove the battery cover on the back of your weather station monitor. ^[viii] The weather station monitor is the part of the clock that displays time, time zone, and weather, as received by the transmitter set upward in previous steps. Insert the three AA batteries into the back. Make sure to utilize the plus and minus symbols to ensure the correct polarity of the batteries.

   • Replace the bombardment comprehend onto the back of the atmospheric condition station.
   • Press the "Reset" button to restart the clock of the weather condition station. The channels of the transmitter volition sync automatically.

6. vi

   Select the time zone. The clock'southward default fourth dimension zone is Pacific, simply if you are not in that time zone, select your real fourth dimension zone. Press and concur the push button labeled "Time" for two seconds. The hr will flash. Utilize the upwardly and down keys to change the hr to the correct hour.^[ix]

   • To alter the time in the correct social club of hour-minute-second-12/24 hr-yr-month-engagement-day linguistic communication, press the fourth dimension key for ii seconds followed by the up and downward arrows to adjust the time. Echo this action one at a time for each time component.
   • Choose PA/P for Pacific, MO/K for Mountain, CE/C for Fundamental, or EA/Due east for Eastern.
   • Press the "Time" key once again to go out the time setting mode.

Advertisement

1. 1

   Insert 1 fresh AA, LR6 ane.5 volt battery into the analog clock bombardment holder. Insert a second AA, LR6 1.5 volt battery into the digital clock.^[10] Ensure that yous insert the battery according to the right polarity on the bombardment. This is indicated past the plus and minus signals on the case and on the battery.

2. ii

   Shut the bombardment embrace. Mount the clock to stand in an upright position most a window so that information technology tin search and receive a signal. The clock will either receive a WWVB point to set itself to the exact time within five minutes of exposure or it volition decide that a signal cannot be received due to the location or time of day.^[xi]

3. iii

   Press the time zone push. Select the time zone that yous are in. The SkyScan diminutive clock can merely collect the right signal from 2,000 miles (3,200 km) away, so it must be set to the right zone to go an accurate reading.

   • Press and hold one of the four time zone buttons MT-Mountain Fourth dimension, CT-Central Time, ET-Eastern Time, and PT-Pacific Time.
   • Clocks tend to automatically default to a Pacific area time zone. If you are in the Pacific expanse time zone, hang up your clock. If non, use ane of the buttons to brand the setting right.

4. 4

   Ready the clock by the window. If y'all choose to manually set the hands, exist aware that it will still get together a signal and adapt the time periodically, overriding manual set ups. Once the SkyScan clock picks up the signal from the NIST station, it volition accelerate by eight seconds until it gets the right signal.

Advertisement

Add New Question

• Question

  Why does the clock proceed blinking?

  

  You need to reset the time. If the fourth dimension is wrong, it will keep blinking until you fix it.

• Question

  How tin I alter it to Fahrenheit without irresolute any other settings?

  

  Try pressing the clock'due south "Gear up" push button repeatedly until the "C" on the clock flashes, then click the "+" button to change it to "F." Alternately, see if there is a button within the transmitter that enables yous modify the transmitter's F/C setting.

• Question

  What do the messages LUN mean on an atomic wall clock?

  

  "LUN" may mean "set the clock to display the lunar (moon) phase." If it says "LON," information technology means the time zone is set up to show fourth dimension in London, England, which is on Universal Coordinated Time (UTC).

• Question

  You said I should install a second battery into the digital clock. How?

  

  Some clocks are designed so that the batteries are inserted in a straight line, merely sometimes simply one tin can be seen. If only one battery is inserted, it will slide back and forth. Slide it completely into the hidden surface area, so put the other battery in right behind it, facing the same mode. Exist sure that proper polarity is observed when inserting them: the flat end is negative (-), the raised bump terminate is positive (+). Other clocks have the batteries inserted side-past-side and both should exist easily visible. They are normally inserted in opposite directions, though at that place are a few exceptions.

• Question

  The 2d hand keeps spinning and doesn't stop. What should I do?

  

  Turn the clock off. You tin do this by switching the on/off push on the back.

• Question

  How practise I change the time zone if I only accept warning-wave-fashion and + and - buttons?

  

  Your phone should say the time, but to utilise the plus-minus buttons it should say in the educational activity handbook on how to set upward.

• Question

  How tin can I fix it to Fahrenheit without changing the other settings?

  

  Click the settings button, then click the temperature and change it to Fahrenheit.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• Brand sure to mountain the clock near a window, so that information technology can receive the signal and update the time often.

• Your SkyScan atomic clock may come with many more features. Read the manual to set them accordingly.

• Manually setting up your SkyScan clock is elementary and straightforward, merely keep in heed that the clock is built to receive signals to fix itself. Whatever you lot do manually volition be overridden as signals are received.

• If it's non receiving a clear indicate and not able to set itself, consider changing the battery or the location.

Cheers for submitting a tip for review!

Advertisement

Things You'll Need

• Fully-charged element of group i batteries (AA or AAA)
• SkyScan Clock
• Screwdriver
• Window

About This Article

Article Summary X

To set an analog SkyScan atomic clock, beginning printing and concur the correct time zone button on the back. You can then ready the hands manually, but they will arrange by themselves when the clock receives a point. To set a digital SkyScan clock, press the time zone button or slide the time zone switch on the back. Then, printing the plus button to bicycle through fourth dimension zones. If your clock has a switch for Daylight Savings Time, make sure this is on or off. Once you've set the time zone, you can manually prepare the time with the plus and set keys, just it will suit automatically when it receives a signal. Regardless of whether your clock is analog or digital, place information technology by a window abroad from any metal or concrete structures so it can pick upwards a signal from the station. Your clock should receive a signal in one case a mean solar day, commonly at 2am. For more tips, including how to set a SkyScan clock with a weather station transmitter, read on!

Did this summary help y'all?

Thanks to all authors for creating a page that has been read 122,819 times.

Did this commodity help you?

Source: https://www.wikihow.com/Set-SkyScan-Atomic-Clock

Share this post